Friday, 12 April 2013

DIY lace print polymer plates


DIY lace jewelry dishes from

This week I have been enjoying myself making these beautiful lace printed jewelry dishes.
Part of their beauty is that they are really easy to make.

By pressing lace into oven bake clay you can get some beautiful patterns....

I am  going to show you how....

DIY tutorial

You will need:
Oven hardening white clay (I used Sculpey original)
Lace or doilies 
A rolling pin
A bowl or similar (used as a "cookie cutter")
Baking paper
Ovenproof dishes (to use for shaping the plates) 
A scalpel
Sandpaper or sanding block 

Lets get started........

1. Knead the oven hardening clay until soft and pliable.
Roll out the clay on a smooth surface like a cookie dough.
Keep rolling the clay with outward strokes until approx 5-6 mm thick. 
Tip: Keep turning the clay over on the work surface to prevent the clay from sticking whilst you roll it out.
Make sure you have enough surface space to measure out the size of the plate you want to make.(in my case: a turned over fruit bowl )

Note:  You'll get nicer edges to the plates if you use a bowl ,similar to this, to push the shape out of the clay, rather than cutting around using a scalpel or knife.

2.Before you press the lace into it, carefully transfer the rolled out clay to a sheet of baking paper. This will help you pick up your finished plate without distorting the shape or leaving fingerprints in the clay, ruining the beautiful pattern you are about to press into the clay.

Make a slight imprint with your "cookie cutter" in the clay, to mark out the area you'll want to print the lace on. Then position the lace/doily and pat down onto the clay. Then using a steady pressure with the rolling pin  carefully press the lace into the clay until level...

Then gently peel off the lace to reveal a beautiful pattern!!

3. Place your "cookie cutter" on the clay and press down firmly and evenly until through.
Then peel away the surrounding clay, leaving you with a disc shape. 
Knead the scraps to repeat processes 1-3, maybe with different lace....

Lift this disc into an ovenproof dish (with the right curvature to make your disc bowl shaped - I used my trusty vintage enamel bowls), with the help of the baking paper its laying on.

4.Bake in the oven in accordance with instructions on your packet of clay.
The Sculpey original that I used, needed approx 15 min per 5 mm thickness at 150 degrees/c*

Do not overbake!

Take out of oven, and leave in the ovenproof dish to cool down for no less than 20 minutes.

5. Whilst the clay is still a bit soft (cheesy), use a scalpel to neaten up the edges of the dishes

6.Then leave for at least another 2 hours to fully cure and harden, before sanding back the edges to finish off the dishes.

........and VOILA! Beautiful dishes to keep jewelry in, or to hang up in a group on a kitchen wall...

I really enjoyed making these, and think they turned out beautiful!! 
The set of 4 dishes I made,only cost me £13.95 for the clay, as I had the other bits and bobs from before.
I am going to look into getting them glazed , as I think they need a protective surface!
So watch out for next week's follow up tutorial:

Thanks for looking and feel free to leave a comment or question below, and I will try my best to answer....



dominika said...

Hi! I left some instructions at hometalk re mica powders :), but having read the full tutorial it hit me that you would not need to cure once more, I mean after it had been baked. Just dampen a section of the bowl (which btw turned out beautiful, will try to do the same :)) with baby wipes and apply mica powders via stencil for example or as it is - with a soft, flat brush. Seal with fixative a couple of times (acrylic spray varnish is great here), and then give it a coat or two of a varnish of your choice. To make it completely scratch proof you would need a thin layer of polyurethane spray varnish at the very end.
ps. the name of your wonderful blog on hometalk is missing 'e' so it would not link here, just thought you may want to look into it...

and see you in a bit, I'm signing on to see what you came up with next.
best regards from a mum to a mum :)

june olsen said...

|Dominika!! Thank you so much....that is unbelievably helpful!!Great to hear from you!! Thanks for the heads up about my link on hometalk...will look into it asap!! best regards!! June

Sharlotte said...

Hi June!
Thanks so much for dropping by to visit my blog! Yes, yes, you are most welcome to become a follower or put me on your blog.
I have been looking around a bit and found the post on these plates. I love them! I want to try them too, thanks for the great tutorial! I'll go back and catch the glazing one too!
Thanks again and have a great weekend.

june olsen said...

Hi Sharlotte! Thank you so much for stopping by my blog!! Glad you liked the tutorial!! looking forward to your next post on your blog!! have good one!!xxjune

Anonymous said...

Love these plates! The link on how to glaze the doesn't seem to be working though and I was wondering if you were ever able to find a good way to glaze them to make them food safe. Thanks!!

june olsen said...

Hi Anonymous! I am working on correcting the link to the glazing tutorial,should be up and running in the next week or so! Sadly there is no way you can make these polymer clay plates foodsafe! Polymer clay is toxic, and not suitable for food stuff!